Original Prusa i3 MK3S/+ to MK3.5 upgrade kit
MK3.5 vám umožní vylepšit MK3S/+ o spoustu nových a užitečných funkcí za velmi rozumnou cenu získáte 32bitovou elektroniku spolu s novým LCD displejem, a také Wi-Fi a LAN konektivitou s podporou vzdálené správy tisku přes Prusa Connect. V neposlední řadě bude rychlost tisku výrazně vyšší díky podpoře Input Shaper a Pressure Advance.Nextruder není součástí upgradu.
Supercharge your MK3S and MK3S+!
With the introduction of the MK4, we were looking for ways to bring its features to our proven workhorse, and the MK3.5 upgrade is the answer. It’s the easiest and most affordable option to print two times faster and expand the capabilities of your MK3S/+ 3D printer!
Enjoy benefits such as super-fast printing with the addition of Input Shaper, sending files wirelessly to your machine without using Raspberry Pi, and navigating the printer’s menus faster than ever before with the new large LCD. The upgrade is straightforward to install and with our detailed assembly guide and 3D printing handbook, you’ll be up to speed in no time!
High-speed printing with ease
As a part of the upgrade package, you will receive our new 32-bit embedded xBuddy to expand your 3D printer’s capabilities. The addition of Input Shaper and Pressure Advance brings a massive boost to your MK3S/+, allowing you to print more than twice as fast and with the same level of quality. The prints that would be otherwise running the entire night can be finished in just a few hours.
Prusa Connect and easy networking
With the MK3.5 upgrade, you also receive an easy way to connect your printer to your network - both wired and wireless. Add the MK3.5 to Prusa Connect, our internally developed remote print management solution, and start sending print files to your printer without the need to deal with USB drives. G-code streaming enables you to start printing mere seconds after you upload the file to the Prusa Connect cloud. However, Prusa Connect can do even more. Check out our article to learn all about it!
Plenty of quality-of-life improvements
It’s time to replace the old segmented LCD with a brand new one. This 3.5’’ color LCD gives you much better control over your printer. See print file previews, read detailed instructions, or scan QR codes - using the printer is now much more convenient. With the new electronics and the new LCD, you can now use standard USB flash drives for storing G-codes, and you can also use a USB drive to flash new firmware (but you can also do it remotely via Prusa Connect). You can customize which information is displayed at all times in the footer of the LCD screen.
Ready for multi-color printing with MMU3
MK3.5 can be enhanced by an optional add-on that allows your single-extruder printer to print with up to 5 colors (materials) at the same time. The MMU3 contains five filament insertion points. Load the five colors of your choice, slice the object with MMU3 profile in PrusaSlicer and start the print. The system automatically selects filament using the selector, loads it into the Extruder and the MK3.5 starts printing. When it’s time to change the color or material, it also happens automatically.
The MMU3 is the latest edition of Multi Material printing device by Prusa Research. The firmware has been rewritten completely, we have redesigned the plastic parts, added more robust metal parts, improved the electronics and updated the filament buffer. All of these changes have improved the reliability and user comfort to levels where MMU has never been before.
To get MMU3 for your MK3.5 printer, you can choose from the following options:
- If this is your first multi-material, get the full MMU3 kit including MMU unit, buffer and spools.
- If you already have the MMU2S unit, get the MMU2S to MMU3 upgrade for MK3.5.
- If you currently own the MK3S+ with MMU3, get this MK3.5 upgrade and the MMU3 cable.
Easy to install
The MK3.5 upgrade is easy to install - we’re providing detailed assembly instructions in seven languages and an updated 3D printing handbook to get you started. You don’t have to worry about getting stuck. Everything has been thoroughly tested in-house. You’ll start printing in no time!
PSU & Heatbed info
Před objednáním upgradu zkontrolujte s jakým zdrojem napájení byla vaše tiskárna dodána a jaká verze konektoru heatbedu je nainstalována. Je to důležité pro správnou kompatibilitu s upgradem. V závislosti na zvolených možnostech vám můžeme zaslat další komponenty, abychom zajistili kompatibilitu s upgradem.
Který zdroj má vaše tiskárna?
- Černý zdroj - vše je v pořádku
- Stříbrný zdroj - budete muset přidat kompatibilní kabelový svazek nebo černý Zdroj (v poli konfigurace výše)
Kolik šroubů má váš heatbed?
- 2+3 šrouby (napájecí kabel spojený šrouby) - vše je v pořádku
- 2+1 šroub (napájecí kabel připájený) - bude nutná výměna heatbedu
Package Includes
Produkt je k dispozici jako stavebnice, kterou si musíte sestavit sami!
Tištěné díly NEJSOU součástí! Prosím, vytiskněte si je dřív než svoji MK3S/+ tiskárnu rozeberete! Filament k vytištění dílů je součástí balení.
Important: The black injection-molded spool holder is not part of the upgrade package. If your printer didn't come with it (early revisions of MK3), you can purchase it here.
Balení obsahuje:
- 32bitová deska xBuddy (stejná jako MK4)
- Kovová skříňka xBuddy (a kryt)
- xLCD obrazovka (stejná jako MK4)
- Kabely pro Nextruder, Heatbed
- Expanzní spoje pro heatbed
- Spojovací materiál a další příslušenství
- Filament pro tisknutelné díly
Součástky, které si ponecháte z MK3S/MK3S+
- Rám a extruze (liší se pouze vzhledem)
- PSU* (stejný výkon/napětí jako u MK4)
- Heatbed MK52 24V (termistor a napájecí kabely budou změněny)
- motory pro osy X/Y/Z/E
- tyče a ložiska pro osy X/Y/Z
Porovnání verzí upgradu pro MK3S/+
MK3.5 upgrade | MK3.9 upgrade | MK4 upgrade | |
Maximální rozměry tisku | 250 x 210 x 210 mm | 9.84 x 8.3 x 8.3 in | 250 x 210 x 220 mm | 9.84 x 8.3 x 8.6 in | 250 x 210 x 220 mm | 9.84 x 8.3 x 8.6 in |
Základní deska | Na míru vyrobená 32bitová STM32 základní deska xBuddy | Na míru vyrobená 32bitová STM32 základní deska xBuddy | Na míru vyrobená 32bitová STM32 základní deska xBuddy |
Drivery krokových motorů | Trinamic 2130 | Trinamic 2130 | Trinamic 2130 |
Krokové motory | Běžné 1.8° X,Y krokové motory | Běžné 1.8° X,Y krokové motory | Precizní 0.9° X,Y krokové motory (prevence „VFA“ povrchových vad) |
podpora MMU3 | Ano | Ano | Ano |
Elektronika extruderu | Ne | Speciální rozbočovací deska pro připojení ventilátorů, termistorů a dalších komponentů. | Speciální rozbočovací deska pro připojení ventilátorů, termistorů a dalších komponentů. |
Vedení filamentu | Hliníkový heatsink (chladič), celokovový hotend | Hliníkový heatsink (chladič), celokovový hotend | Hliníkový heatsink (chladič), celokovový hotend |
Systém pohonu | Přímé podávání filamentu | Nextruder planetová převodovka, poměr 10:1 | Nextruder planetová převodovka, poměr 10:1 |
Kalibrace první vrstvy | Manuální doladění Z | Plně automatické (díky Load Cell senzoru) | Plně automatické (díky Load Cell senzoru) |
Quick-Swap systém trysek | Ne | Ano | Ano |
LCD obrazovka | 3.5″ grafický displej s 65 tisíci barev | 3.5″ grafický displej s 65 tisíci barev | 3.5″ grafický displej s 65 tisíci barev |
Kalibrace tiskové podložky | Automatická, Mesh Bed Leveling | Automatická, Mesh Bed leveling (pouze na tiskové ploše) | Automatická, Mesh Bed leveling (pouze na tiskové ploše) |
Tisk jedním kliknutím | Ano | Ano | Ano |
Stavové LED | Ano | Ano | Ano |
Input shaper | Ano | Ano | Ano |
Senzor filamentu | Ano (IR) | Ano (vestavěný Hall senzor) | Ano (vestavěný Hall senzor) |
Loadcell senzor | Ne | Ano | Ano |
Pokročilé senzory | 3 termistory, SuperPINDA, senzory otáček ventilátorů | Filament senzor, Load Cell sensor, zotavení po ztrátě napájení („Power panic“), 4 vysoce precizní termistory (originální Semitec) + monitoring otáček ventilátorů | Filament senzor, Load Cell sensor, zotavení po ztrátě napájení („Power panic“), 4 vysoce precizní termistory (originální Semitec) + monitoring otáček ventilátorů |
Ochrana před výpadkem proudu | Ano | Ano | Ano |
Ethernet připojení | Ano | Ano | Ano |
Wi-Fi připojení | Ano | Ano | Ano |
Prusa Link | Integrovaný | Integrovaný | Integrovaný |
Tiskové médium | USB disk / LAN / internet pomocí Prusa Connect | USB disk / LAN / internet pomocí Prusa Connect | USB disk / LAN / internet pomocí Prusa Connect |
Aktualizace firmware | USB disk | USB disk | USB disk |
Cena stavebnice | 6 490 Kč (vč. DPH) | 12 999 Kč (vč. DPH) | 14 990 Kč (vč. DPH) |
Koupit MK3.5 upgrade | Koupit MK3.9 upgrade | Koupit MK4 upgrade |
Recenze
Prodávající neověřuje, zda zveřejněné recenze pocházejí od spotřebitelů, kteří zboží, digitální obsah nebo službu skutečně zakoupili či použili. Recenze jsou poskytovány registrovanými uživateli PRUSA ACCOUNT.
Ke stažení
Příprava objednávky: 1-3 pracovních dnů.